Technical Data Sheet - Fast-Set™ Extreme
Product Name
Bonstone® Fast Set™ Extreme
Manufacturer
Bonstone Materials Corporation
Download Technical Data Sheet PDF
 397
KB File
Product Description
A two-component exterior grade epoxy adhesive which cures
at below freezing temperatures. Extreme is packaged for convenient handling in applications relating to contractor restoration, doweling, and general bonding.
Basic Uses
- Outstanding cure profile (Cures at below freezing temperatures) Achieves
90% of full cure within one hour at room temperature
- Structural bonding of natural stone, concrete, masonry, metals, wood, etc
- Anchoring and doweling
- Spot bonding of heavy duty stone tiles
- Seals cracks and around injection ports prior ro pressure-injection grouting
Limitations
Use on stone free of oil, grease, wax, coatings and other contaminates.This
product will yellow on exterior exposure to sunlight. Due to strong
odor this product is recommended for exterior use.
Applicable Standards
Indiana Limestone Institute specifications for units preassembled with
thermosetting resins.
Technical Data
Cured Properties
| Mix ratio |
1 part FS41 Extreme Part A to
1 part FS41 Extreme Part B by volume |
| Mixed viscosity |
Knife Grade |
| Pot life @ 75°F |
15 minutes |
Mixed Properties
| Initial Set Time @ 75°F |
15 minutes |
| Full cure time @ 75°F |
within 24 hours |
| 90% of full cure at 75°F: |
60- minutes |
| Property |
Values |
Test Methods |
| Tensile Strength: |
2414 psi |
ASTM D-638 |
| Tensile Modulus: |
852634 psi |
ASTM D-638 |
| Tensile Elongation: |
0.2% |
ASTM D-638 |
| Compressive Strength: |
6947 psi |
ASTM D-695 |
| Compressive Modulus: |
161416 psi |
ASTM D-695 |
Installation
Surface Preparation and Use
Use gloves, wear eye protection, and avoid skin contact. When grinding
cured joints, wear a dust mask. Substrate to be bonded must be completely
dry and dust free. Mix only the amount of epoxy which can be used in
10 minutes. Avoid stressing joint before complete cure of epoxy. Mask
areas which must be kept free of epoxy. Clean uncured epoxy from tools
with toluene or xylene. (Use caution, these solvents
are flammable. Ensure local ventilation.) Remove cured epoxy mechanically.
Mixing Instructions
The unmixed epoxy components should be at or above 45°F. Combine
the two ingredients at the following volume ratio: one part A to
one part B. Mix thoroughly--- ingredients must be blended homogeneously
for proper cure. Best to mix using double mix method. See reverse side.
Temperature
Dependency
This product is unique and cures at below freezing temperatures. Most
setting properties are independent of curing tem- peratures between 20°F
and 100°F.
Coverage
Approximately 30 square feet per gallon when applied at 50 mils (1/16th
of an inch). 231 cubic inches per gallon.
Availability
Packaging and Storage
Bonstone® Fast Set Extreme is available in quarts, gallons,
5 gallon pails and cartridges .
Shelf life is approximately one year if kept in unopened cans in a dry
area at 75°F.
Warranty
This product’s warranty is limited to replacement of defective
material and freight charges to destination only. Bonstone Materials
Corp. is not responsible for consequential damages.
Maintenance
Designed for application in areas inaccessible to maintenance procedures.
Technical Service
Specification Service
- Specifications for various applications
- Specification writing dept.
for unique applications
This information is furnished without
warranty, representation, inducement, or license of any kind, except
that is is accurate to the best
of Bonstone Material
Corporation's (BMC) knowledge or obtained from sources believed
by BMC to be accurate, and BMC does not assume any legal responsibility
for use
of reliance
upon same. User must determine if the product, process, or
information described is suitable to the intended application. Before
using any
chemical, read
its label and Material Safety Data Sheet.
<Back | Top | Home
|
